 |  |
| Club Foot | Pro Arm |
| We supply three types of swing arms, two are pictured above and a third is not shown is the same as the Pro Arm with the addition of our weld-on axle block assembly. All are available for Kawasaki and Suzuki in 4" to 12" over stock in 2" increments. The Club Foot would commonly be used with an 18" x 6" wheel using an 8 1/2" wide tire. The Pro Arm would use the 15" x 9" wheel and a 10" tire. All three versions come complete with our axle adjusters and a heat treated 4130 chrome moly axle in your choice of 20mm, 7/8" , or 25mm . These units feature our usual high quality and are sealed for use as a pressurized air storage unit . We can also weld on wheelie bar mounts at the time of manufacture . |
| When ordering, please specify the following: Make and model of frame, axle diameter desired, tire width, and amount over stock length. |
| C200 | Club Foot | 4" to 12" over stock | $545.00 |
| C201 | Pro Arm | 4" to 12" over stock | $629.00 |
| C202 | Pro Arm | 4" to 12" over stock with adjustable axle height | $880.00 |
| C203 | Upper & Lower wheelie bar mounts | add to above | $175.00 |
| C204 | Brake Rod | 5/16 or 3/8 rod ends | $44.00 |
| C205 | Lengthen stock swing arm | Starting at | $198.00 |
| | | | |
Rear swing arm or frame extension made from 1 3/4" X 1" X .065 4130 chrome moly tube. Slotted to allow 2" axle adjustment. Aluminum components are 6061 - T651 and adjustment rod is 3/8" - 16 grade 8. Overall length is 8 1/2"
C178 20mm axle C180 7/8" axle C179 3/4" axle C181 25mm axle
Per set....................$99.00
Aluminum axle block, end cap and threaded adjuster. For use in 1 3/4" X 1" X .065 chrome moly tubing. Same as above if you prefer to supply your own tubing.
C182 20mm axle C184 7/8" axle C183 3/4" axle C185 25mm axle
Per set....................$69.00
Upper and Lower Wheelie bar mounts weld-on Comes with, 2 top pieces and 2 bottom pieces
C186.......... $64.00
Axles Our axle nuts have a large flange so there is no need to use a washer. When ordering an axle, let us know the outside width of the swing arm. The rear axles include two nuts, one will be heli-arc welded to the end |
| C206 | Front axle - 15mm PH17 - 4 stainless | $80.00 | | C207 | Rear axle - 3/4" PH17 - 4 stainless | $96.00 | | C208 | Rear axle - 20mm PH17 - 4 stainless | $103.00 | | C209 | Rear axle - 7/8" 4130 heat treated chrome moly | $106.00 | | C210 | Rear axle - 25mm 4130 heat treated chrome moly | $108.00 | | C220 | Rear axle - 1" 4130 heat treated chrome moly | $130.00 | | C221 | Rear axle - 28mm 4130 heat treated chrome moly | $150.00 | | C222 | Rear axle - 1-1/4" 4130 heat treated chrome moly | $190.00 | | C216 | Axle nut - 3/4" - 16 - 4142 heat treated with integral washer | $27.50 | | C217 | Axle nut - 7/8" - 14 - 4142 heat treated with intetral washer | $27.50 | | C218 | Gas tank neck & cap with O-ring seal 1-1/2" diameter tube | $60.00 |
| | 
|
